Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Installation Across Alameda
Gate installation in Alameda is a different job than it is across the bay. The island’s marine air works on metal year-round, and a century of custom homebuilding means very few gates are a standard size. We plan for rust, salt, narrow lots, and Victorian trim before we ever dig a post hole. If you’re dealing with a sagging ornamental iron gate on the Gold Coast or a swollen wooden gate in the East End, call (628) 227-2771 and we’ll give you a written price before any work begins.
Why Latch and Post Gate Repair San Francisco Is Alameda’s Preferred Gate Installation Company
Alameda homeowners call us because we know what their gates are up against. The salty breeze off the bay corrodes hinges, rots post footings, and seizes latch hardware that would last decades inland. We’ve replaced operator control boards on pre-2000 Viking and FAAC systems throughout Alameda, and we’ve custom-welded hinge plates to match the hand-forged ironwork on Victorians near Franklin Park. The job is never just “hang a gate and go.” It’s making sure the new gate respects the house it’s attached to.
Cody Beckman, who leads our gate work, has crews factory-trained on LiftMaster, FAAC, BFT, Linear, and Viking equipment. That means when an Alameda customer has a 1990s FAAC board fail, we can usually say within the first visit whether it’s worth repairing or should be replaced outright. We show up in uniform, we’re background-checked, and we lay drop cloths and wear shoe covers before we step inside. Your floors stay clean, and you get a photo of the cleanup before we leave. That’s the Cedarwell C.A.R.E. routine: Clean up, Ask before we touch anything, Respect quiet hours, Explain the price first.
Styles & brands we work with
Gate Installation Services in Alameda
Gate Installation Services in Alameda cover everything from a new pedestrian gate on a narrow-lot Craftsman to a full double swing gate on a bay-side property. Most homes here need custom work, because the rough opening between two 1920s stucco piers was never built to a modern spec. We measure on site, quote a written price, and schedule the work around your family’s routine.
Custom Gates for Older Homes
A new gate on a Victorian or Craftsman should look like it’s always been there. We build to match existing trim profiles and match hinge styles to the period of the house. If the existing ironwork has ornamental scrollwork, we can often reuse it and build a new frame behind it.
Driveway and Pedestrian Gates
Standard driveway gate installation in Alameda generally runs $2,800 – $6,500 depending on steel gauge, motor type, and whether we’re working with a single or double gate. Pedestrian gates are typically $900 – $2,400. Everything is quoted and agreed before work starts.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Electric Gate Installation in Alameda
Electric Gate Installation in Alameda means more than bolting on an opener. Many of these homes still have gate posts set in old concrete that shifts after decades of bay wind and soil movement. We check post depth, footing condition, and gate weight before recommending an operator. A new electric swing gate system for a standard single driveway typically runs $4,200 – $7,800 in Alameda, installed, with the operator, safety photocells, and keypad entry.
Operators for Legacy Posts
Not every old post is worth keeping. We’ve seen plenty of Alameda posts that look fine above ground but have rotted or rusted through at the footing. In those cases, we set a new steel post in concrete and weld a hinge plate that matches the original. Adding an operator to a failing post is the fastest way to a broken gate.
Modern Safety Requirements
New electric gate installs in Alameda include UL 325-compliant safety edges or photocells, and we wire everything to current code. If you’re upgrading an older manual gate to electric, we’ll check whether the gate geometry itself can support a modern opener. Some 1920s gates with hand-forged hinges are too heavy in the wrong places, and we’ll tell you straight rather than sell you something that fails in a year.
Trusted Brands We Service in Alameda
We install and service FAAC, BFT, Linear, Ghost Controls, DoorKing, Elite, and Mighty Mule operators, and we work on Viking and LiftMaster systems throughout Alameda. Since we’re part of the Cedarwell family of gate specialists, our techs have seen thousands of these boards and motors. When your BFT control board dies and you’re told “they don’t make that one anymore,” we can usually tell you what current model drops in without replacing your whole gate.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Installation Problems We See in Alameda Homes
- Obsolete control boards: Pre-UL 325 operators made before 2000 often can’t accept modern safety photocells. In Alameda, where fog and salt shorten electronics life anyway, a dead board is usually the point where we recommend a full operator replacement rather than chasing discontinued parts.
- Rotted hinge posts on original iron gates: Hand-forged hinges from the 1890s and 1920s are works of art, but the posts holding them are often oak or fir set directly in dirt. After a century of fog, the footing is gone. We see this constantly on Gold Coast Victorians, where a new operator adds torque to a post that was already failing.
- Swollen wooden gates in the East End: Persistent morning fog keeps moisture in wood year-round. We get calls every summer about gates that won’t close because the stiles have expanded and bound against the frame. Sometimes the fix is planing and resealing. Sometimes the frame has warped past that, and a new gate is the cheaper answer.
- Bay-side corrosion on hinges and latch hardware: Gates within a few blocks of Shoreline Drive or Crown Beach rust the hardware first, often while the gate panels still look fine. A technician can often guess which part of Alameda a gate came from by where the rust is concentrated.
Pricing for Gate Installation in Alameda, CA
We Also Serve Cities Near Alameda
Our Gate Installation crews cover the whole bay, and we regularly work in Oakland, Berkeley, San Leandro, and San Francisco. If you’re in Alameda or just over the Park Street Bridge, call us and we’ll schedule a time that works for your family.
Serving Alameda, CA - Our Local Coverage Area
We’re based in the Alameda area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Alameda
Not always. Many original ornamental iron gates on Alameda Victorians are rebuildable. We can often reuse the gate itself, fabricate a new steel frame behind it, set a new hinge post, and add a LiftMaster or FAAC operator with safety photocells. If the original hinges are intact and the gate is square, you might spend $4,200 – $6,800 instead of replacing everything. We’ll tell you in writing what can be saved and what can’t. Call (628) 227-2771 for an assessment.
Salt air and morning fog are the cause. In Alameda, homes near Shoreline Drive, Crown Beach, and the marina sit in marine air that deposits salt on metal hardware every night. That salt accelerates oxidation, especially on hinges, latch springs, and bolt heads. We use marine-grade stainless hardware on bay-side installs and coat exposed steel with rust-inhibitive primer before painting. It costs a little more, but it lasts years longer.
Yes. Narrow-lot bungalows often have shorter gate runs and less room for conduit, which makes solar a practical choice. A solar opener from Ghost Controls or Mighty Mule can usually be installed for $3,200 – $5,500 on a single pedestrian or driveway gate, depending on the battery and panel size. There’s no trenching, no electrician, and the system works fine in Alameda’s foggy climate because the panels charge steadily all day, not just in direct sun. We’ll give you a written price before anything is ordered.
Often yes, depending on the model. If the Viking board is from the last 10 years and still available, we can swap it for roughly $700 – $1,400 parts and labor in Alameda. If the unit predates modern safety standards and can’t accept photocells, replacing the whole operator is usually the smarter money. We’ll show you both numbers in writing and let you decide.
Usually, it’s resetting the hinge post or replacing the hinges themselves, not the whole gate. On a Craftsman, the original gate may be in fine shape while the post has rotted at ground level. A new post set in concrete with a welded hinge plate typically runs $700 – $1,500. That’s a fraction of a full replacement, and good for another 20 years. Call (628) 227-2771 and we’ll come measure it.
Written by Cody Beckman, Owner at Latch and Post Gate Repair San Francisco, serving Alameda homeowners with gate installation, repair, and electric gate work since 2009.